Need help in writing C code for SPI controller
Forums: Zedboard Hardware DesignHello, I have been doing a project. I am using Vivado 2016.4 and Zedboard. In my project, I have to use the SPI port of Zynq as a master and this to be interfaced with...
View Articleusing AES-Z7EV-7Z020-G for my project
Forums: Zedboard Hardware Designhello i am going to use AES-Z7EV-7Z020-G to make my project,but i dont know what langue this proccer is working , is there compiler that i can download to train...
View ArticleDebug with ILA on zedboard
Forums: Zedboard Hardware DesignHello everybody I am using vivado logic analyzer to debug the output from my hls design. How can i configure the analyzer to capture the data when multiple interrupts...
View ArticleZedBoard + ALI3 Display + Linux
Forums: Zedboard Hardware DesignHello, I'm trying to make the 7-inch Zed Touch Display (http://zedboard.org/product/7-inch-zed-touch-display-kit) usable in a Zedboard with Linux. I need to develop my...
View ArticleUltraZed 3EG Starter Kit - Display Port Design 2017.2_FAILED: to open display
Forums: Zedboard Hardware DesignHello everybody, I own the "UltraZed-EG Starter Kit" (Black) (XILINX ZYNQ UltraScale+ XCZU3EGTM-SFVA625AAZ + UltraZed-EG IO Carrier Card: Rev 1-01-05). Now I tried to...
View ArticleSPI interface design
Forums: Zedboard Hardware DesignI am creating a project for SPI and I have connected a zynq processor and SPI interface in standard mode. I want it to be in master mode and only one slave to be...
View ArticleHDMI output for hardware design
Forums: Zedboard Hardware DesignHello, I want to display a gray scale image (stored in a BRAM of the Zedboard) on my laptop screen via the HDMI output. Can you provide me with HDMI data sheet,...
View Articlezedboard and NT1065 through SPI
Forums: Zedboard Hardware DesignI'm interested in Interfacing Zynq (through Zedboard) to peripheral slave devices via SPI. and I have to connect the FMC connector of zedboard to NT1065. Since I have...
View Articlezedboard and NT1065
Forums: Zedboard Hardware DesignCan anyone tell me the .ucf file for NT1065 for zedboard. I am trying for SPI between these two boards but not finding the pin constraint file for that. if you have a...
View ArticleZYNQ interrupt from PL
Forums: Zedboard Hardware DesignHow can i interrupt the PS from PL without AXI-GPIO? For example : My RTL design will send some signal to PS. How can i use these signal to interrupt PS ? What should i...
View Articlesource code for i2csensor app
Forums: Zedboard Hardware DesignAnybody know where I can find the source code for the i2csensor app? I'm looking to use the ST accelerometer in my own code and the source code would be useful for...
View ArticleConnecting a GigE Camera to my Zedboard
Forums: Zedboard Hardware DesignBasically I was wondering if it were possible to connect an Allied Vision GigE camera to my zedboard? I am using the Mako G030B model, and was hoping to be able to...
View ArticleConnecting a GigE Camera to my Zedboard
Forums: Zedboard Hardware DesignBasically I was wondering if it were possible to connect an Allied Vision GigE camera to my zedboard? I am using the Mako G030B model, and was hoping to be able to...
View Articlecan I write my own SPI interface controller in VHDL only
Forums: Zedboard Hardware DesignHello, I have one of Zedboard, i need to interface a external board which will be connected to the SPI interface. There are only a few input/output pins, clk, enable,...
View ArticleUsing FMC for massive GPIO breakout
Forums: Zedboard Hardware DesignHi! I'm not sure if this is the right forum for my question and also I'm not completely sure if I got the underlying topic right. We want to use the FPGA on the Zedboard...
View ArticleDUMPING ETHERNET DATA TO PL WITHOUT OVERHEAD
Forums: Zedboard Hardware DesignHi everyone, I would like to redirect Ethernet payload comming/going from/to Eth0 port on zedboard without requiring intervention from PS (although it can provide...
View ArticleUsing the XADC with PMOD headers
Forums: Zedboard Hardware Design Hello, I am working on a project in which i need to measure an analog signal on the Zedboard, preferably on the PMOD header(s). Looking around the forums I have seen...
View Articlezedboard ｕsb0 and usb1
Forums: Zedboard Hardware DesignHi zedboard.org, I am working on zedboard, which contains 3 mini USB interface, e.g., usb-jtag, usb-uart, usb-otg. In Vivado block diagram, I am able to allocate zynq7...
View ArticleRELATED TO ZYNQ VIVADO(AXI IIC IP)
Forums: Zedboard Hardware DesignHello , i need to use AXI iic IP with custom code in zynq vivado. a zynq processor can read and write to the I2C custom logic which is connected with the PL. I didnt...
View ArticleRELATED TO XADC ZYNQ
Forums: Zedboard Hardware DesignHello, In our design, for internal XADC interfacing we have used C20,B20,E17 & D18 pins of the zynq (XC7Z007S-1CLG400) as input pins for XADC. What is the voltage...
View Article